Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
What're your ideas about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is easily available, the task can move rapidly; if you have to open up a wall to eliminate the old bathtub as well as position the new tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will require a helper to leave the old tub and embeded in the brand-new one. Ensure you have actually certified on your own for the job as well as are comfortable attempting it. Rather than working with a professional to take over a halfway-completed task, it is better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This write-up will certainly aid you set up a new bathtub in your shower room if you have actually already acquired a brand-new tub as well as don't need to transform the setup of your previous supply of water pipelines.
Your tools as well as product checklist need to make up the following:
Planning for the Setup
To start with, the sustaining frame provided with the bath needs to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to prevent stress on the tub.
Fit the flexible tap ports to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Before carrying on to fit the new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, put the bath tub in the needed placement. The wood boards are useful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost versatile faucet port to the appropriate supply pipe by making a compression join; after that do the very same for the other faucet.
Turn on the water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill up the tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait till the tub has actually been utilized at least when as this will resolve it into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in position with the manufacturer provided backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap adapters. The former type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to split a rigid seal, triggering the water to permeate the wall between the bath and also the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealant can split fairly very early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently readily available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic person who reads on How to Install a Bathtub, I imagined sharing that portion was necessary. Liked our article? Please share it. Let somebody else find it. I value reading our article about How to Install a Bathtub.
Tap issues? Ring! Report this page